Política de Cookies
 
El titular del presente sitio web, espacio, o aplicación (en adelante, el "Contenido") informa a los usuarios de que puede utilizar dispositivos de almacenamiento y recuperación de datos (de manera genérica, denominados "cookies") cuando un usuario navega por el Contenido.
Home

portada2DASEL is a company specialized in the development of high-end ultrasound technology. We offer at the same time flexible solutions according to each client requirements. Therefore the quality level in our products has not been neglected. Quality is a commitment that DASEL applies in all production areas to maintain traceability of manufactured products. For this reason the company has been certified ISO 9001:2015 by Bureau Veritas in the equipments production and calibration.

portada DASEL develops all its products with a modular architecture and using high-density re-configurable devices (FPGAs). Given the high cost for new hardware development, this design philosophy allows to adjust our systems to many different applications, with the incorporation of new functions or specific algorithms with no need to upgrade the equipment electronics.

 
 

Sello PYME INNOVADORA 22/02/2022    Seal of Excellence DASEL     ISO-9001 ISO-9100 
        ISO 9001:2015 ISO 9100:2018
 
PYME INNOVADORA
Válido hasta el 22 de febrero de 2022
escudo de MEIC 22/02/2022
         

logo AAENDE   logo AEND   logo CDTI   logo CLUSTER AEROESPACIAL   logo HISPAROB  logo ICEX   logo pesi   logo PTFE

Last blog post

ULTRACOV project get funded: Novel ultrasound scanner to face COVID-19 disease challenges

ultracov imagen ultrasonido pulmon

The project ULTRACOV aimed at developing a novel ultrasound scanner to face COVID-19 disease challenges: early diagnosis and following of patients evolution leaded by DASEL get funded by last CDTI call.

This project obtained funding from the las call of the Spanish Institution “CDTI” (July 2020) in a very competitive call for R&D projects to face the health emergency COVID19. ULTRACOV  This development is led by DASEL SL, a Madrid SME based in Arganda del Rey. The Ultrasonic Systems and Technologies Group of the CSIC (GSTU-CSIC) and the Nuclear Physics Group Group of the Complutense University of Madrid (GFN-UCM) will also participate. The participation of the emergency ultrasound service of the Hospital Universitario La Paz guarantees the clinical approach at all stages of the development of the ultrasound system, and will carry out the first trials with patients.

The project duration is 18 months, (starting July 2020) and clinical trials of the prototype are planned to begin in early 2021.

The objective of the ULTRACOV project is the development of an ultrasound scanner oriented to the early detection and monitoring of the COVID-19 disease, specially designed for situations of pandemic and high healthcare pressure. Through interactive artificial intelligence tools that simplify the examination and interpretation of images, and a design oriented to operation in high-risk conditions (easy disinfection, ergonomics, etc.), the aim is to extend lung ultrasound to a greater number of professionals and services, from primary care to intensive care. The impact on the capacity of the healthcare system for the management of COVID-19 patients would be very positive, since it is a very specific tool for evaluating the lung condition at all stages of the disease, including potential chronic problems. in the medium and long term. Furthermore, it would be useful for the diagnosis and management of patients with other lung pathologies, potentially serious in certain groups (pediatric patients, pregnant patients, etc.).

 

 

Pin It

Sector                         : Eolic Energy

Material                     : Glass-Fiber Composite

Technology                : Phased Array

Equipment                 : SITAU-311-PRT

Keywords                  : Phased Array, GFRP, Aerogeneradores

Title                            : Detection of broken fiberglass in wind turbine blades

1. Introduction

Non destructive evaluation of windmill blades using ultrasound is a challenging task. Microstructure of fiberglass and resin composites (GFRP) introduces dispersive effects on ultrasound waves, which is seen as grain noise and produces high attenuation to ultrasonic signals. The traditional approach to overcome these problems is using low frequency transducers (typically 500 kHz), at the expense of loosing resolution, and hence, the capability to detect small defects or to inspect low thickness components.

In this work, results of the inspection of a thin GFRP layer (3mm) using phased-array technique are presented. The goal is to detect the presence of broken fibers in the material. A 5MHz array was used, along with a novel C-Scan processing technique, that allows to detect broken fibers with a resolution above 1 mm.

2. Materials and Methods

A phased array with 128 elements, inter-element pitch of 0.5mm and 5 MHz was used, in contact with the flat surface of the inspected part (see Figure 1). A SITAU-311-PRT equipment was used, with 32 channels multiplexed to 128 array elements, and linear B-Scans at 0º were performed.

Figure 1 – Inspection scheme

3. Results

The inspection goal is to detect broken fibers in a 3mm thickness layer of GFRP material. Shown images were obtained in field, from a real windmill blade, with a 500mm length cut in the inner glass-fiber layers.

Figure 2 (right) shows three of the B-Scans acquired along the fiber cut. As the ultrasonic pulse is not able to individually resolve each one of the glass fibers, what is seen in the images is an interference pattern between the echoes received by all fibers in the fabric. Relative position between fibers changes in the damaged zone, and so that, interference pattern also changes.

Presence of broken fibers does not necessary mean that received amplitude will decrease, because glass-fiber layers can become overlapped in the curing process. In that case, fiber damage cannot be detected by means of conventional amplitude C-Scan ( figure 2 left ).

DASEL has developed a novel processing algorithm (GFRP-Scan®), based on the interference pattern analysis, that is capable to detect broken fibers also at very low thickness layers ( figure 2 center ). As signal processing is based on global information contained at each B-Scan, it is little sensitive to configuration parameters, and hence, a very robust evaluation method.

Figure 2 – Images from a windmill blade with a 500mm length cut in the inner GFRP fibers. (Left) Conventional C-Scan (Center) GFRP-Scan®

(Rigth) Several B-Scans at different positions.

4. Conclusions

Beam focusing capability of phased array systems allows using higher frequencies when inspecting GFRP components and so that, a much higher resolution can be achieved compared to traditional low frequency transducers. In this work, the feasibility of detecting broken glass fibers in a 3mm thickness GFRP layer was demonstrated.

GFRP-Scan® algorithm, included in the ScanView® software and available for all SITAU models, allows detecting small defects in fiberglass layers with high reliability. Its effectiveness has been proved by the inspection (in field) of more than 50 blades before being installed in a wind farm.

5. References

4. Links to equipment used

-          SITAU-311-PRT

Pin It

Facebook News

Last Tweets

Latest industry news

Wind Power News & Analysis RSS Feed

29 November 2021

Read the latest wind industry & renewable energy companies, policy, wind farm projects & technology news, analysis on Windpower Monthly

Industrial Scanners

Aerospace Inspection Solutions

Flaw Detectors

Ultrasonic Flaw Detectors

Phased Array

Guided Wave

Pulser-Receivers

Integrated Inspection Systems

Bar Inspection Systems

Tube Inspection Systems

NDT Systems Instrumentation

 

 

 

 

Advanced NDT applications

GLASSFIBER BROKEN FIBERS

GLASSFIBER UNBOND

RAILWAY STEEL BOLTS

CASTING INCLUSIONS

AUTOMOTIVE NODULARITY

Applications

Application Notes

Applications Support

PDF Library

Video Gallery

Software Downloads

Training Academy

Obsolete Products

ISO Certifications

 

 

Update client